Hey Quaker Hill, are your tires worn out? What is the standard for our CT streets? How can you tell on your sedan?

While there may be legal requirements for the Quaker Hill area, there are safety concerns that go beyond meeting minimum replacement mandates.

2/32 is the depth of the tire tread wear indicator bars that US law has required to be molded across all tires since August 1, 1968. When tires are worn so that this bar is visible, there’s just 2/32 of an inch – 1.6 millimeters – of tread left. It’s that level of wear that’s been called into question recently.

We’re referring to the Consumer Reports call to consider replacing tires when tread reaches 4/32 of an inch, or 3.2 millimeters. And the recommendation is backed by some very compelling studies.

The issue is braking on wet surfaces in and around Quaker Hill. Most of us think of our brakes doing most of the work, but if you don’t have enough tread on your tires, the brakes can’t do their job. When it’s wet or snowy, the tread of the tire is even more critical to stopping power.

Picture this: you’re driving over a water covered stretch of road near Quaker Hill, CT. Your tires must be in contact with the road in order to stop. That means that the tire has to move the water away from the tire so that the tire is actually contacting the road and not floating on a thin film of water.

Floating on the surface of water is called hydroplaning. So if there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.

In the study a section of a test track was flooded with a thin layer of water. If you laid a dime on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up were brought up to 70 miles per hour, or 112 kilometers an hour and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths:

• New tire tread depth
• 4/32 of an inch
• 2/32 of an inch

So what happened with the 2/32 tires on the car? Get this – when the car had traveled the distance required to stop with new tires, it was still going 55 miles an hour. Stopping distance was nearly doubled to 379 feet and it took 5.9 seconds.

Wow! That means if you barely have room to stop with new tires, you would hit the car in front of you at 55 miles an hour with the worn tires.

Now, with the partially worn tires – at 4/32 of an inch – the car was still going at 45 miles an hour at the point where new tires brought the car to a halt. It took nearly 100 feet more room to stop and 1.2 seconds longer. That’s a big improvement. We can see why Consumer Reports and others are calling for a new standard.

Of course, stopping distances were greater for the heavier pick-up truck.

How do you know when your tires are at 4/32 of an inch? Easy; just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

You may remember doing that with pennies. A penny gives you 2/32 to Abraham Lincoln’s head. The quarter is the new recommendation – 4/32.

How do people feel about replacing their tires earlier? Well, tires are a big ticket item and most people want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out?

For us, and we would guess for many, the answer is “no”.

Pennell’s Auto Center
26 Norwich Rd.
Quaker Hill, CT 6375
860-440-2630

Share this post via...

At Pennell’s Auto Center we hear from a lot of people who are excited about the new diesel engines that will soon be available in passenger cars and SUV’s. But our CT friends are often curious about the preventive maintenance requirements. People may not know that diesel engines have long been used extensively in Europe and Asia. In fact, in some markets, there’re nearly as many diesel powered passenger cars as there are gasoline.

Here’s who’s announced or is expected to announce new diesels for North America: BMW, Mercedes, Audi, Volkswagen, Nissan, Honda, Toyota, Hyundai and Subaru. Of course, the US auto makers will be expanding their diesel offerings as well. Diesels will become a very big deal here in CT.

You may ask, why has it taken so long getting to CT and North America? There are a bunch of reasons like fuel tax policies and such, but the biggest hurtle was that CT diesel fuel had a high sulfur content – too high for the latest generation of highly refined diesel engines. Recent government mandates to remove sulfur now opens up CT to the engines the rest of the world’s been enjoying for a long time.

Why are diesels so popular worldwide? Well, for starters, diesels get up to 30% better fuel economy than gas engines. And they last a lot longer. And modern diesel engines are refined, quiet and powerful – and there’s none of that black smoke we used to see.

Some people may think that diesels create more pollution. But, you need to rethink diesels. Environmental pollution standards for diesel cars and light trucks are scheduled to be as strict as they are for gasoline vehicles. A modern diesel engine is as clean as a gas engine.

You may also have heard a lot in the news about bio-diesel. The exciting thing about diesels is that they’re not limited to fossil fuels. They can run on fuel made from vegetable oil. There are refineries that make diesel fuel from cellulosic waste like woodchips from lumber mills. There’s even this cool new process where a special strain of algae is used to convert carbon dioxide, water and sunshine into bio-diesel. That’s still a ways off, but you can see that diesel can become a sustainable source of fuel.

And, there are not a lot of trade off’s with diesel in terms of performance. A modern passenger car diesel is very smooth, quiet and quick. Most folks wouldn’t notice any difference. For those who tow trailers and haul heavy loads, diesels will be an improvement.

Now diesel engines are heavy duty, so they cost more than gas engines. But they get better fuel economy – so the break-even point is largely dependent on the difference between CT gas and diesel prices at the pump and how many miles you drive. And diesels have a higher resale value.

Now, let’s get back to diesel maintenance. You have to keep in mind that most of the new diesels are just coming in, or will be over the next couple of years, so we don’t have the maintenance schedules to make direct comparisons yet.

But going off what we already have in CT, we can expect fluid drain intervals to be similar to gasoline engines. Diesels do require very clean fuel, air and oil, so their filters are much higher capacity than gasoline filters and cost more. The engine air filter needs to be changed more frequently as well.

Repair costs are similar. As with gasoline engines, proper maintenance is the key to long engine life and to avoiding repairs. So pretty much what we have come to expect with gas vehicles; coolant system service, transmission service, power brakes, power steering, differential, filters, fuel system, and so on. And the payoff for you, if you’re the kind that likes to keep your vehicles for a long time, is that a properly maintained diesel engine can last for hundreds of thousands of miles.

Share this post via...

There are a surprising number of small, inexpensive parts that can lead to expensive engine damage when they fail. It doesn’t seem right.

Fortunately a lot of those things can be taken care of in routine maintenance. They may not be easy to remember, because it is a long list, but your service center at Pennell’s Auto Center can help you know what’s scheduled to be taken care of.

Some of us in Quaker Hill CT really don’t look forward to going in for an oil change and then getting a list of the other things the manufacturer recommends.

But automotive maintenance is all about prevention, and addressing small problems before they get big. Let’s take the fuel filter for example.

You may not know this but the median age for private vehicles on our Quaker Hill CT roads is over nine years. When cars get older, five years or so, they’ve accumulated a lot of dirt and rust in their gas tanks. If that dirt gets into the engine it can cause thousands of dollars worth of damage. So somewhere between that dirty gas tank and the price of a great vacation – is the lowly fuel filter: a very inexpensive part that doesn’t cost too much to replace. And your car’ll just run better too.

A clogged fuel filter can’t let enough fuel through. You might notice at first that your car is running fine around town, but struggles or sputters on the Quaker Hill CT freeway or when you accelerate. Enough fuel can’t get through to meet the demands of higher speed. If it gets bad enough your engine might just shut off or not start at all, which could be dangerous.

Some fuel filters have a bypass. When they get clogged, they allow dirty fuel to move around the filter element so dirt ends up in the engine. We’ve already talked about how expensive that can be.

The fuel filter is even very important for newer cars. The fuel is still dirty even if there isn’t rust in the tank. It’s just that the fuel filter will need to be changed more frequently as the vehicle gets older.

How often should you change your fuel filter? Check your owner’s manual. Your Quaker Hill CT service advisor at Pennell’s Auto Center can tell you as well. It’s usually around thirty thousand miles or so. Ask if it’s time for a full fuel system cleaning as well. They often go hand in hand.

It’s good to know that your Quaker Hill CT service center has your back. When you’re motivated to maintain your vehicle’s performance and to reduce operating costs, you’ll think of Pennell’s Auto Center as your ally – and maybe even your memory.

Share this post via...

Make an appointment with Pennell’s Auto Center to have your on board diagnostics analyzed.
26 Norwich Rd.
Quaker Hill, CT 6375
860-440-2630

Today we’re going to talk about on-board diagnostics and the questions we hear from folks around Quaker Hill CT who need answers about diagnostic services. They want to know what diagnostics are, what’s involved and what the benefits are. They really want to understand the value of diagnostic scans by a trained technician in Quaker Hill CT.

These are valid concerns. If you don’t understand something it’s really hard to know its value. Let’s start with some history.

Since 1996, all cars and light trucks in Quaker Hill CT have been required to use a standardized diagnostic system to help repair technicians determine what’s wrong with your vehicle. The diagnostic system works with the vehicle’s Engine Control Module – the computer that controls many engine functions.

The computer monitors dozens of components and processes. Depending on what the sensors read, the computer will make adjustments to compensate for conditions and minor problems. When there is a condition that it can’t adjust for, the computer will turn on the check engine light.

It is also called the ’service engine soon’ light on some vehicles. The warning light signals you to get into your Quaker Hill CT service center so that the trouble code can be read and the problem can be fixed. Your service center will have a scan tool and powerful software that will help the technician diagnose the problem.

If you’ve searched for check engine light on the internet, you may have seen that you can buy an inexpensive scanner or go to an auto parts store to have the trouble code read to tell you exactly what’s wrong.

That’s a common myth. The code itself doesn’t tell you what’s broken. It starts you looking in the right place. It tells you what engine parameter is out of range – but it won’t tell you what’s wrong or how to fix it.

Let’s say you think your daughter has a fever. You take her temperature and it reads one 102 degrees. You’ve confirmed a fever, but you don’t know what’s causing it. Is it a 24 hour flu, an infection, appendicitis or leukemia? A fever is a symptom of all of these medical problems, but it takes a skilled physician’s examination and additional diagnostic tests to find out what is actually causing the fever.

An example of a trouble code could be: P0133, which reads ‘Bank 1 sensor 1 circuit slow response’. This means that the front oxygen sensor has a slow response time to changes in the air-fuel mix. If that’s all you knew about cars, you would think your oxygen sensor was broken and would replace it. Now, it could be the oxygen sensor – but it could also be a bad or contaminated airflow sensor, exhaust leak, electrical problem, an intake manifold leak or any of a number of other things.

You can imagine a lot of oxygen sensors have been replaced because of that code. So the on-board diagnostics point the way to where the trouble lies, but it takes some skill and high-tech equipment to actually pinpoint the problem. The cheap scan tools that a consumer can buy do not have the ability to retrieve some of the operating history that’s stored in the engine control computer. That history’s very helpful in diagnosing the problem. Service centers like Pennell’s Auto Center invest a lot of money in high-end diagnostic tools to help solve the mystery and get you back on the road as soon as possible without replacing a lot of parts that don’t need replacing.

So, on-board diagnostics provide a powerful starting place for a highly-trained, well-equipped technician to get to the bottom of your problem. When your check engine light comes on, get it checked at Pennell’s Auto Center. If the light burns steady – don’t panic. Get in to Pennell’s Auto Center soon to have the engine scanned. A flashing check engine light means that there is a severe engine problem. Get in as soon as you can – waiting too long can lead to very expensive damage.

And try to not drive at high speed or tow or haul heavy loads with a flashing check engine light.

Share this post via...

Having trouble with your fuel system? Bring your sedan into Pennell’s Auto Center for a check up.
26 Norwich Rd.
Quaker Hill, CT 6375
860-440-2630

Today we’re talking about fuel system cleaning. The first thing to know is how important it is to have a clean fuel system. You need fuel to go, and the cleaner your fuel system, the more efficiently the fuel will burn. That means more power and better fuel economy.

A clean fuel system saves money at the pump. We guess you could say, it all starts and ends at the pump. One of the most important things you can do to keep your fuel system clean is to buy good quality gas. Major brands have detergents that keep gum and varnish from rapidly building up in the fuel system.

So buying cheaper gas can actually cost you in the long run. Now, most cars on the road are more than five or six years old. That means they’ve had time for some dirt and rust to start accumulating in the fuel tank. This junk needs to be filtered out of the fuel before it hits your engine. That’s the fuel filter’s job.

When the fuel filter is clogged, the dirty fuel will bypass the filter and go on up to the engine where it can clog fuel injectors and get into the cylinders. That could do some damage. So you should have your fuel filter changed when recommended. Check your owner’s manual or ask your service advisor if your fuel filter is due for replacement.

The fuel then goes up into the throttle body. This is another area where varnish and gum can accumulate. A professional fuel system cleaning will use a combination of special cleaning chemicals and old fashioned swabbing to clean out the throttle body. Now, the fuel injectors are the last stop in the fuel delivery system.

It’s real important to keep those fuel injectors clean. The fuel injectors need to deliver a precise amount of fuel, at exactly the right time, in a particular spray pattern. They just can’t do that if they’re dirty. Dirty fuel injectors really rob power and waste fuel.

It is important for the fuel system proper, but there are a couple other things that will help keep your engine clean as well. Of course, air is mixed with the fuel before it’s burned. Dirty air means dirt gets into your engine, so you need to replace your engine air filter when it’s dirty.

The PCV value routes unburned fuel that escapes into the lower engine back up into the intake system to be burned. A sticky PCV valve needs to be replaced to make sure that system is working properly and the breather filter needs to be replaced if it’s dirty as well.

Do all these things and your engine’s air and fuel will be as clean as possible. You’ll get much better fuel economy and better power

.

Share this post via...

We find that a lot of Quaker Hill service and repair at Pennell’s Auto Center are a little tentative when they talk with their automotive advisors. They want to ask questions, but don’t want to be embarrassed or to seem pushy. Cars are very complicated and there’s more to know about them than most of us have the time to learn. Maybe it’s because cars have become so much more reliable that the average person just doesn’t need to know as much to keep their vehicle on the road.

You know, your local hospital has a Patient’s Bill of Rights that they post throughout the hospital. We think our Quaker Hill automotive service customers also have a right to ask any question they need to understand what is wrong with their car and what it will take to fix it. They need to feel free to ask the cost and benefits of recommended services. And they certainly have a right to understand the financial end of the transaction.

It’s all about the communication. It’s a little harder when you’re trying to find the right service center in Quaker Hill. But once you’ve developed a relationship, the communication should come easier.

What are some of the barriers to communication? Well, let’s go back to the medical example. When your doctor’s explaining something to you, it’s something that she understands very well and is very familiar with. So she may use jargon you don’t understand or that you don’t have the education and training that’s foundational to understanding what she’s trying to explain.

So you fall behind and get frustrated.

It can be the same with your Quaker Hill automotive service advisors. Most of them are very busy trying to service and fix cars to get their customers back on the road. So, just ask when you feel you need more information.

Financial related issues seem to be most frustrating to customers. If you’re not sure, ask what the payment policies are. For example, there’s a big difference between giving your car a quick once over and doing a thorough inspection. Diagnosing a problem may take quite a while. Make sure you know what’s done as a courtesy and what has a fee. Remember, you still have to pay for the office visit even if the doctor says you only have a cold.

Communication is a two way street. If you have some real budget concerns, ask your Quaker Hill service advisor what he can do. He can give you priorities and options. He can tell you what needs to be taken care of right away for safety or financial reasons. Then you can work out a plan for when to get the rest done. He can also help you with options on the parts. The preference is to always use a high-quality part with a reputation for reliability. But if money is real tight, he might be able to find a rebuilt part or a used part. He should tell you the difference in the guarantee for the part so you can make a good decision.

Ask about warranties for parts and labor. Be sure to get all the paperwork you need to make a possible claim in the future. Your service center and its technicians stand behind their work and want you to understand precisely what that means.

Be sure to ask for and keep a detailed explanation of all the work that’s done on your vehicle. These records will help you keep track of service, warranties and document the good care your vehicle has received when the time comes to sell it.

Call Pennell’s Auto Center to make an appointment.
26 Norwich Rd.
Quaker Hill, CT 6375
860-440-2630

Share this post via...

People in Quaker Hill have been hearing a lot about higher oil change intervals these days. Maybe you’re wondering: What are the key issues?

Some new vehicle manufacturers in Quaker Hill are now recommending much higher oil change intervals than they have in the past. As much as 5,000 to 8,000 miles or more. This practice came under scrutiny when four of the largest new car manufacturers announced that owners like those in Quaker Hill were experiencing engine damage resulting from these higher oil change intervals.

The manufacturers’ standard oil drain service for particular vehicles was scheduled at around 7,500 miles. People following these recommendations were experiencing engine damage. It turns out that oil sludge was building up. This caused small oil passages to clog and engine parts to fail.

What causes oil sludge? It’s a factor of time and mileage. There are hot spots in every engine that cause oil burn off that leads to sludge. Also, water from normal condensation can build up in the oil. This water also creates sludge. Severe driving conditions lead to more rapid sludge formation.

Visit Pennell’s Auto Center in Quaker Hill, CT 6375

Severe driving around Quaker Hill includes short trips under four miles or trips under ten miles in freezing conditions. The engine just doesn’t get warm enough for the water in the oil to evaporate.

Severe conditions are at the heart of the problem. Stop-and-go driving, towing, dusty conditions, heavy loads, very hot or very cold temperatures, a car top carrier – these are all conditions that would suggest that the severe service schedule should be considered.

The severe service schedule has much shorter oil change intervals. People in Quaker Hill just need to honestly evaluate how they drive to determine if they should change their oil closer to the severe service schedule, or to the standard schedule.

Some types of sedan will give oil change reminders. But it’s important to know how that reminder is determined. For some, the reminder simply comes when the standard mileage interval has rolled around. Others use a computer algorithm that takes into consideration the number of cold starts, trip length, engine temperature and so on. It’s programmed to approximate where on the standard/severe service spectrum you fall. Some more expensive vehicles actually have sensors that test the cleanliness and effectiveness of the oil.

For the rest of us, better safe than sorry should be the guiding principle. Talk with your Quaker Hill service advisor at Pennell’s Auto Center and work it out together. Find out what kind of oil the factory sends out in your vehicle. Sometimes it’s a premium grade that costs more than standard oil – but it may be what’s needed to meet a higher factory recommended interval.

If you’re realistically conservative, standard grades of oil will take care of you year after year. If you want to push the limits, ask for a premium grade oil to give you extra protection.

So, what happened with those manufacturers with the problems from higher oil change intervals? They ended up extending the engine warranty for parts that were affected by oil sludge. But they had a stipulation – they lowered the oil change interval and the vehicle owner had to provide proof of oil changes at the new lower interval to keep the extended warranty.

Share this post via...

Screeching tires, crunching metal – it’s an accident! If you’ve ever been in a car accident in Quaker Hill, even a minor one, you know how upsetting it can be. It’s hard to think straight and know what to do.

Let’s review what you should do in case of an accident:

When an accident occurs, you should always stop. Leaving the scene of an accident in Quaker Hill is considered a crime – even if it’s not your fault. And hit and run penalties are fairly severe, possibly resulting in steep fines, loss of your CT driver’s license or even jail time.

Your jurisdiction may require that you try to help someone who is injured by calling for help or performing first aid if you are able. Warn other Oakdale and Niantic motorists by putting out flares, using your flashers or lifting your hood. Call Quaker Hill emergency services as soon as possible. Tell the operator if medical or fire help is needed.

Always file a Quaker Hill police report. It’s tempting to skip this if everything seems to be ok. But without a police report, the other guy can say whatever he wants about the accident later, and you’ll not have an objective report to help defend yourself. Discuss the accident only with the police. Emotions are strong after an accident and we naturally want to talk about it – don’t. Never admit fault or guilt to anyone including the police officer. Sometimes we may feel at fault, but in the eyes of the law, the other guy is responsible.

Truthfully give the officer the facts: such as “I was going thirty miles an hour” not “I wasn’t speeding”. Remember, anything you say to the officer or anyone else can be used against you.

Also get the officer’s name and ID number and ask where you can get a copy of the accident report.

Get the facts on the driver and owner of the other vehicle:

• Name
• Address
• Phone number
• Date of birth
• Driver’s license number and expiration
• Insurance information

Also take down a description of the other Quaker Hill vehicle, license plate and vehicle identification number. Most CT auto insurance companies don’t record license plate numbers, so the VIN number is the best way to track the vehicle.

Ask witnesses, including passengers, to wait for the police. If they can’t wait, ask for contact information and request that they write a brief description of what they saw. If someone refuses to leave their name, write down their license plate number so the police can track them down later if necessary. Always call your insurance agent or your insurance company. Call or see a physician if you think you may have been injured. For vehicle repairs, call Pennell’s Auto Center at 860-440-2630

Contact Pennell’s Auto Center to learn more about what do do in case of an auto accident.
You can find us at:
26 Norwich Rd.
Quaker Hill, CT 6375
Or call us at 860-440-2630

Pennell’s Auto Center and AutoNetTV hope that you never have to use this information and wish you happy Quaker Hill travels.

Share this post via...

All modern vehicles come with fuel injection systems, so it’s a topic we all need to know something about. All new cars and trucks sold in Quaker Hill, CT over the last 30 years or so have come with fuel injection systems.

The fuel injector is a valve that delivers the gas or diesel fuel to the right place, in the right amount, at the right time; to be mixed with air and burned in the engine.

So how many fuel injectors does your car have? There’s one for each cylinder. So four, six or eight for most folks in Quaker Hill, CT. Some vehicles have 10 or 12 cylinders. The engine control computer makes adjustments to the fuel injector as it monitors the engine and other sensors. Fuel injectors are a pretty sophisticated part.

Pennell’s Auto Center can help you with a fuel injector cleaning service. What’s the benefit? In order to work right, the fuel injectors have to deliver the fuel at a precise pressure at a very precise time. The fuel needs to be sprayed in a particular pattern as determined by the engine design.

Over time, varnish can start to build up in the fuel injectors, effecting the pressure, pattern and timing of the fuel charge. The result is that the fuel doesn’t get burned as efficiently as it could. That robs performance and wastes fuel.

What about dirty fuel – how does that affect the fuel injectors? The fuel injectors are the last stop in the fuel system. It starts at the fuel tank. Frankly, the best way to keep your fuel injectors working well is to use high quality fuel. Its real tempting to shop for bargains with fuel prices as high as they are, but major brands in the Quaker Hill, CT area have better detergents and additives and deliver consistent quality.

What about a good fuel filter? The fuel filter is the next device in the fuel system. Its job is to filter out the dirt and rust that collect in the fuel tank. If it’s clogged up, the dirt will bypass the filter and head upstream to the fuel injectors.

It’s important to replace the fuel filter when your manufacturer recommends it. That’s part of a comprehensive fuel system cleaning.

There are different kinds of fuel injection systems. Port fuel injection systems, the kind most gasoline engines have, operate at 60 pounds per square inch. The injectors for the new gas direct injection engines we’re starting to see require 10 to 30 times as much pressure. And some diesel engines for passenger vehicles have injectors that operate at 30,000 pounds or more per square inch. There’s no room for dirt and gum in a precision part like that.

There are a lot of good products available in Quaker Hill, CT that can clean fuel injectors. They’re best used to prevent fouling in the fuel injectors. Many can’t clean a seriously gummed up injector – that requires a professional deep cleaning. But putting the cleaner in the fuel tank after you’ve had Pennell’s Auto Center take a look at your fuel system will help keep it clean. Be sure to read the label for directions.

Give us a call if you think your sedan may be ready for a fuel injector cleaning.

Manager: Joseph Pennell
Pennell’s Auto Center
26 Norwich Rd.
Quaker Hill, CT 6375
860-440-2630

Share this post via...

We live in such a disposable society here in Quaker Hill. It’s amazing all the stuff we throw away.

New stuff comes out so fast, we just toss the old and move on. It seems like when we were kids, our parents were real sticklers about taking care of our stuff. You know, hang up your clothes, polish your shoes, put away your toys. If something got lost or ruined by neglect, tough – we had to do without.

We couldn’t afford new cars very often, so we tried to make them last as long as we could. It’s a good thing that cars are more reliable these days.

They just don’t break down as often. And the good news for us penny pinchers is that a modern car can easily go 200,000 miles with proper care. The engineering’s there and so is the manufacturing quality. The missing ingredient is us making sure we follow the manufacturer’s recommended maintenance schedules.

Is it really that bad to get off schedule? Well, it all adds up. Every time you go a couple thousand extra miles between oil changes, you’ve created an opportunity for sludge to form and clog passages. Then some parts don’t get oiled and they start to wear out faster.

Skip a cooling system service, and the corrosion inhibitors become depleted, and the radiator starts being damaged – one step closer to a failure. The same thing is true for transmission service, power brakes, fuel system cleaning – really everything on your schedule.

It’s also even more important for older vehicles. Those engines and other systems have had more time to get dirty, so they’re a bit more stressed anyway. But it’s never too late to get back on track with your maintenance and to hold off further damage.

It’s just another example of our parents being right. (Surprising how often that happens.) And it really does start with the oil change, just like Dad said. When you get a full service oil change they top off all your fluids and check for other items that are on your maintenance schedule. That’s like your safety net – go in for oil changes on time, and let your service advisor at Pennell’s Auto Center help you keep track of the rest.

Of course, some things are going to wear out along the way, stuff like alternators, water pumps and such. But that stuff is cheaper than a new car payment. And taking care of problems early means they have less time to cause other problems. It’s like having high cholesterol – you don’t want to wait for a heart attack before you address it.

Share this post via...